您好,欢迎访问无锡合达电子设备有限公司官网!
0510-83212339
13861812138
无锡合达电子设备有限公司
您的位置:首页 > 新闻动态 > 行业知识
联系我们

无锡合达电子设备有限公司

地址:无锡市梁溪区惠钱路55号25幢
电话:13861812138

咨询热线13861812138

厂家介绍高温老化房的特点和注意事项

发布时间:2018-12-12人气:259

高温老化房性能特点:采用库板单元组合,内容积可任意放大,拆装容易,老化房可依客户需要尺寸设计,并配合顾客扩厂时的迁移。科学的空气流通设计,避免任何死角,使室内温度分布均匀。每个老化房产品都根据客户的要求订做,保证了设备的适用性和高效、节能。极高的稳定性及实用性。完美的外观、合理的设计。使用的安全及高可靠性。超静音。可扩展性。

Performance characteristics of high temperature aging room: using the combination of warehouse plate units, the content area can be arbitrarily enlarged, easy to disassemble and assemble, the aging room can be designed according to the size of customers'needs, and cooperate with the migration of customers when expanding the factory. Scientific air circulation design, avoid any dead angle, so that indoor temperature distribution is even. Every aging property is customized according to the requirements of customers, which ensures the applicability, high efficiency and energy saving of the equipment. Extremely high stability and practicability. Perfect appearance and reasonable design. Safety and high reliability in use. Super quiet. Extensibility. 高温老化房的安全预防

Safety Prevention of High Temperature Aging Room

1、在使用电气动力时,必须事先检查电开关,马达以及机械设备各部分是否安置妥善。

1. When using electric power, it is necessary to check in advance whether the electric switch, motor and mechanical equipment are properly installed.

2、始工作时和停止工作时,必须将开关彻底扣严和拉下。

2. When starting and stopping work, the switch must be completely fastened and pulled down.

3、在更换保险丝时,要按负荷量,不得加大或以铜丝代替使用。

3. When replacing the fuse, the fuse shall be replaced by copper wire according to the load, and shall not be increased or replaced by copper wire.

4、严禁用湿手、湿布或铁柄毛刷等去清扫和擦拭电闸刀、电插梢等,防止触电。

4. It is strictly forbidden to use wet hands, wet cloth or iron handle brushes to clean and wipe switch knives, electrical plugs, etc. to prevent electric shock.

5、凡电气动力设备过热时,应立即停止运转。

5. When the electric power equipment is overheated, it should stop running immediately.

6、凡使用110伏以上电源装置,仪器的金属部分必须安装地线。

6. Ground wires must be installed in the metal part of the instrument when using power supply devices above 110 volts.

7、易燃、爆炸、易挥发性物质试样的试验及储存

7. Test and Storage of Flammable, Explosive and Volatile Substances

8、腐蚀性物质试样的试验及储存

8. Testing and Storage of Corrosive Substances

9、生物试样的试验或储存

9. Testing or Storage of Biological Samples

10、强电磁发射源试样的试验及储存

10. Testing and Storage of Samples from Strong Electromagnetic Emission Sources

辛苦整理!转载请注明来自 http://www.chinasavant.cn/show.asp?id=112

推荐资讯

13861812138